Turbo-action 23254 Turbo Hydro 350 Pro Auto 1-2 Shift Valve Bod Manuel d'utilisateur télécharger pdf

Part #23254 1 2/92, 2/07, 6/09

CHEETAH COMPETITION WITH AUTMATIC 1-2 SHIFT

Part #23254

Turbo Hydro “350” 1969-80 (Non-Lockup) PRN321

Installation Instructions

FIRST, READ INSTRUCTIONS CAREFULLY, THEN PROCEED TO INSTALL VALVE BODY BY FOLLOWING

EACH STEP INDIVIDUALLY.

Kit Includes: 1 - Valve Body

1 - 23093 Special Valve Body Spacer Plate

1 - 23096 2-3 Performance Plate

1 - 23097 Spacer to Valve Body Gasket (Small)

1 - 23098 Spacer to Case Gasket (Large)

1 - 23099 Pan Gasket

1 - 23130 Modulator Plug

1 - 23345 Governor Shift Point Kit

NOTE: Plate included in this kit will fit *all Turbo-Hydro “350” non -lockup transmissions even though it may

not look the same as the plate presently in your transmission. Spacer Gaskets included in this kit

must be used. Note will not fit Turbo “250”.

STEP #1: Transmission should be cool before installing. Also, place gear shift selector in neutral. If

vehicle is on the ground, secure so it will not roll.

STEP #2: Remove drain plug in pan and drain oil. Olds., Buick and Pontiac do not have drain plug, and

therefore, must be drained by dropping transmission pan. Recommend leaving a couple of

bolts attached until most of the oil has drained.

STEP #3: Remove transmission oil filter by removing two screws. Be careful not to lose gasket.

STEP #4: Remove kickdown valve wire by pulling pin out of kickdown lever in valve body (Fig. #1).

STEP #5: Before removing valve body, note position of the gear shift linkage hooked to the valve body

(Fig. #2). Remove 17 bolts from valve body. CAREFULLY lower valve body and at the same

time slide angled shift pin lever from gear shift selector. DO NOT drop valve body or manual

valve with angled shift pin.

STEP #6: Holding spacer plate with your hand, remove spacer support plate bolts. CAREFULLY lower

plate as there are four small teflon balls sitting on plate. Also, watch that the governor screen

and oil pump screen do not fall out. These screens are located in case underneath the valve

body spacer plate. See Fig. #3 & #4. Olds., Buick and Pontiac have two governor screens in

rear of case, one in each passage. Chevy has only one governor screen.

STEP #7: Sometimes the front servo will fall out when lowering the spacer plate in STEP #6. If so, be

sure to reinstall per Fig. #5.

1535 Owens Road, Jacksonville, FL 32218

Phone (904)741-4850 *** FAX (904)741-4853

1 2 3 4 5 6

Résumé du contenu

Page 1 - Installation Instructions

Part #23254 1 2/92, 2/07, 6/09CHEETAH COMPETITION WITH AUTMATIC 1-2 SHIFTPart #23254Turbo Hydro “350” 1969-80 (Non-Lockup) PRN321Installati

Page 2 - 2 2/92, 2/07, 6/09

Part #23254 2 2/92, 2/07, 6/09STEP #8: Using vasoline, place oil pump screen and governor screen or screens into place.STEP #9: Install Spe

Page 3 - Figure #15

Part #23254 3 2/92, 2/07, 6/09Figure #15#4 #3Remove #2#2#1Teflon Ball LocationRemove#1Remove

Page 4 - MUST BE REINSTALLED

Part #23254 4 2/92, 2/07, 6/09CAUTION: If Spacer Support Plate is not put backper drawing below, you will have a noreverse/no high gear condi

Page 5 - 5 2/92, 2/07, 6/09

Part #23254 5 2/92, 2/07, 6/09FIGURE #1KICKDOWN ASSEMBLYFIGURE #2GEAR SHIFT LINKAGEFIGURE #4OIL PUMP SCREENFIGURE #3GOVERNOR SCREEN LOCATIO

Page 6 - FIGURE #6

Part #23254 6 2/92, 2/07, 6/09FIGURE #6GOVERNOR WEIGHTS AND SPRING CHARTWEIGHTSHeavy 1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Turbo-action 23254 Turbo Hydro 350 Pro Auto 1-2 Shift Valve Bod Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Turbo-action 23254 Turbo Hydro 350 Pro Auto 1-2 Shift Valve Bod. Turbo Action 23254 Turbo Hydro 350 Pro Auto 1-2 Shift Valve Body (PRND21) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Turbo-action 23254 Turbo Hydro 350 Pro Auto 1-2 Shift Valve Bod