Turbo-action 24144 & 24145 Turbo Hydro 400 Pro Street Manua Manuel d'utilisateur télécharger pdf

Part #24144/24145 1 1/73,7/99,9/02,3/03

CHEETAH Manual/Automatic Valve Body - PRN321 Stock Pattern

Part #24145

(PRN321)

Turbo Hydro “400”

1971-Up

Part #24144

(PRN321)

Turbo Hydro “400”

1965-70

1535 Owens Road, Jacksonville, FL 32218

Phone 904-741-4850 * Fax 904-741-4853

1535 Owens Road, Jacksonville, FL 32218

Phone (904) 741-4850 *** FAX (904) 741-4853

www.turboaction.com

Installation Instructions

First, READ INSTRUCTIONS CAREFULLY, THEN PROCEED TO INSTALL THE VALVE BODY KIT BY

FOLLOWING EACH STEP INDIVIDUALLY.

Valve Body

Kit Includes: 1 - 24144 Valve Body 1965-70

1 - 24145 Valve Body 1971-Up

1 - 24114 Special Valve Body Spacer Plate

1 - 24148C Pan Gasket

1 - 24149 Spacer to Valve Body Gasket (Small) O.E.M. #8623561

1 - 24150 Spacer to Case Gasket (Large) O.E.M. #8623563

STEP #1: Transmission should be cool before installing. Be sure vehicle is secure to prevent rolling.

Drain oil by carefully removing transmission pan bolts. Recommend leaving a couple of

bolts partially attached until some of the oil has drained.

STEP #2: Remove transmission filter. If 1968 or newer model, remove retaining bolt, hold pipe that

filter is connected to and then pull filter off.

STEP #3: Before loosening valve body, note how the gear selector lever connects to the manual

control valve in the valve body. Fig. #3.

STEP #4: Remove bolts from valve body and then carefully remove governor tubes and valve body

together. Avoid bending governor tubes. If 1970 or newer model, disconnect white wire

from the valve body. Also, be sure the manual control valve doesn’t slide out.

NOTE: Sometimes the Intermediate Servo will fall out when removing the valve body, Fig. #2.

STEP #5: Remove the two bolts holding the downshift solenoid and valve body spacer plate. Make

sure you support the spacer plate with your hand. Lower the plate with steel balls

carefully.

STEP #6: Using Special Valve Body Spacer Plate #24114, lay one of the new Valve Body Gaskets

at a time behind plate and be sure all holes are open. Place petroleum jelly on case side

of Valve Body Spacer Plate and place larger gasket on that side being sure all holes line up.

STEP #7: Install Balls #1 and #6 on new plate #24114 with petroleum jelly, Fig. #4. If 1965-70,

discard Balls #2, #3, #4 and #5. If 1987-Up, discard Balls #2, #3, #4, #5 and #7.

STEP #8: Remove manual control valve from old valve body and place into your new valve body.

1 2 3 4

Résumé du contenu

Page 1 - Part #24144

Part #24144/24145 1 1/73,7/99,9/02,3/03CHEETAH Manual/Automatic Valve Body - PRN321 Stock PatternORPart #24145(PRN321)Turbo Hydro “400”1971-UpPart #2

Page 2 - Use with 24144

Part #24144/24145 2 1/73,7/99,9/02,3/03STEP #9: Remove governor tubes from old valve body. Note on some late models, the governor tubeclosest to dr

Page 3 - Selector Lever

Part #24144/24145 3 1/73,7/99,9/02,3/03CAUTIONBe sure that Manual Control Valvelines up with selector pin on theselector lever!Selector LeverFig. #3

Page 4 - Steel Ball Locations

Part #24144/24145 4 1/73,7/99,9/02,3/03#1Discard#2Ball#3#4#5#6Figure #4Steel Ball LocationsDiscard#3Ball#2Discard#4BallDiscard#5BallReinstall#1BallRe

Commentaires sur ces manuels

Pas de commentaire

Turbo-action 24144 & 24145 Turbo Hydro 400 Pro Street Manua Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Turbo-action 24144 & 24145 Turbo Hydro 400 Pro Street Manua. Turbo Action 24144 & 24145 Turbo Hydro 400 Pro Street Manual/Automatic Valve Body (PRN321) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Turbo-action 24144 & 24145 Turbo Hydro 400 Pro Street Manua